double glazing window repair Glazing Door Lock Repairs

Is your uPVC window or door mechanism faulty? Maybe the handles on your uPVC windows and doors aren't aligned properly or are difficult to use.

It is crucial that your double glazed window repairs glazed doors function smoothly, or else you'll lose energy and increase the chances of burglary. Owen the Locksmith will be able to repair your door lock at a reasonable cost.

Snapped Key

If a key breaks in the lock, it can be incredibly difficult. It also poses a security risk, as the door might not lock and leave you vulnerable to intruders. There are fortunately quick fixes you can attempt to fix the issue and get your door operating properly once more.

Be sure to remain calm. If you panic, you could end up pushing the damaged key piece further into the lock.

Spray WD-40, or any other penetrating lubricant, into the lock. This will help the broken piece be removed more easily. You can also employ a screwdriver in order to break pieces that could be hindering the flow. If you're lucky enough to have a small piece of the key sticking out and you want to remove it, make use of a paperclip, or any other thin metal object to grab it and remove it. Both methods work, but you must be careful not to push the damaged key further into the keyway.

Some paperclips come with grooved edges that can be used as hook extractors. Jigsaw blades also work well for this. If you don't happen to have one of these tools then you can bend a hook with needle-nosed pliers. Also, a pair tweezers is a good way to grasp and remove the remaining bit of the broken key.

If you are unable remove the broken piece of key Use a lock deicer. This is usually found in most hardware stores. It works by freezing any moisture or ice that may be in the lock.

If none of these solutions work, it may be time to contact a locksmith. The experts at Fitlocks can quickly fix issues such as broken handles and snapped keys with uPVC locks and door mechanisms. They can also reconfigure your double glazed repair glazing door mechanisms to make them easier to operate. You can request repairs to your double-glazing online or contact us to discuss your needs.

Broken Cylinder

A damaged cylinder could pose a serious security risk. It's a good thing that it's a simple repair for an expert locksmith to complete. A locksmith will have to tap the cylinder in order to repair it. They can do this using a hammer or other tool, but the best way is to make use of a long match or piece of wire. Then, position the match's tip or wire close to the keyway. After this, the locksmith will hit the lock to break it open. This is much safer than using a heavy hammer that could harm the lock.

Overheating is the primary reason for cylinder heads to crack. This can happen when the block and the cylinder head are made from different metals such as cast-iron and aluminium. Different metals can be heated and cool at different rates. This can cause localized hotspots to expand faster than the rest of the cylinder.

Another possible cause for cracks in the cylinder is corrosion. If the cylinder head and cylinder block are not maintained properly, this could cause corrosion or rust that could cause them to expand at greater rates than they should. This can lead to cracks in the future.

If your uPVC window or door lock is rigid and requires a lot more pressure to turn it could be due to a variety reasons. A malfunctioning locking mechanism, misalignment or a worn handle are common reasons for this issue.

Fortunately, this is an easy and inexpensive fix for most homeowners of double glazing. A professional locksmith is able to solve the issue within one hour of arriving at the property. Based on your requirements, they can replace the locking mechanism, change the window handles, and also change the gearboxes. A professional locksmith will be able to inform you of the most cost-effective option for your home. They may recommend upgrading to 3 Star TS007 Euro Cylinders, which offer an additional layer of protection from burglars. It's a small price to pay for the security that comes from knowing your uPVC doors are safe.

Broken Handle

It's not a surprise that window handle locks could break. They have complex mechanisms that wear out over time. It can be difficult to determine the cause of the problem and repair it correctly.

Fixing the broken handle, regardless of whether it's the internal locking mechanism or latch can increase the security of your uPVC door and reduce the risk of draughts. It is costly to repair double glazing window or replace your handle incorrectly and it could also harm the frame and the lock of your door.

With the window in the open position then loosen the screw holding the handle by using a screwdriver. The screw should be located on the inside of the backplate. It is typically hidden by a screw cap to enhance the appearance. It is important to not be able to replace any internal parts of the handle, such as the levers and plates on either side. Keep them in the same order to make it easier to replace them if needed.

Next, turn the handle to make it 90 degrees to the window frame. Finally, loosen the screw at the back of the handle that fixes it to the internal spindle with a second screwdriver. Once the screw is free, you can take the handle off and take the broken spindle out. Replace this with a new one, making sure it is the same length as the previous one (you can usually find these on the internet or in hardware stores) and then securely screw it into the correct position. Be careful not to overtighten because this could cause damage to the handle or the window frame.

Close the handle and test it. It should function smoothly and you'll be able to open your windows after a few times.

Don't forget to double-check that your uPVC window is shut correctly when you're working with the handle. If they're not then you may experience damp and draughts inside your home as well as compromising your home's energy efficiency. Core Sash Windows is a local window company that can adjust the hinges of the window frames to ensure that they shut correctly.

Broken Spindle

It is more typical for the spindle to break than the handle. This is most typical in uPVC tilt and turn windows. These types of windows require a handle which acts as a locking mechanism within the window frame. The handle is attached to a centre rod that triggers a set of mushroom-like locking cams, these secure the frame of the window. If the dead latch mechanism fails to open when the handle is turned, it's likely the spindle is damaged. This could be a frustrating issue.

There are ways to fix this issue. A good locksmith will be able to quickly and effectively address this problem. They can remove the window handle using a tool that can remove the wheel portion of the mechanism that is where the spindle goes. This can be done without damage to the handle or window frame.

Once the wheel is removed the technician can then examine the spindle to determine what caused it to break. This involves disassembling the spindle and inspecting every component, observing any damage or excessive wear. This procedure is usually done in a clean environment by skilled technicians.

The next step is to clean the damaged spindle, this will remove any debris or dirt that could be hindering its normal function. After this, the spindle could be repaired or replaced. If it is replaced, the technician can take the dowel that is similar in size to the one used in the first and drill mating holes into both parts of the spindle. This ensures that the new spindle is a precise fit with the handle.

If the spindle is damaged and cannot be repaired, it might need to be replaced entirely. Home centers offer generic replacements, but if the design of your window is unusual then you will need to find a woodworker or cabinet maker who can replicate the exact part for you. Once the new spindle has been installed it can be fitted to the handle by line up the holes for screws in the handle and the frame existing screws. Once the new handle is firmly installed, you are now ready to operate your uPVC window.